Porozmawiajmy

Let's Talk

Precyzyjne Prowadzenie Manualne GPS dla ciągnika

#products

Precyzyjne Prowadzenie Automatyczne dla ciągnika

#company

FieldBee Tractor GPS Navigation App Premium Subscription

#app

#blog

#for_partners

#faq

#team

#careers

logo_en

SM_en

Play Market

SM_1

SM_2

SM_3

Be happy with Fieldbee

title

img_en

<div><span>The Auto Calibrate procedure guides the operator through the calibration process for the active vehicle. The calibration steps teach the ECU-S1 system the characteristics of the vehicle and the steps are critical to achieve optimal control performance.</span><h2>Note the following:</h2><ul><li>Before beginning the calibration process, the vehicle and oil in the vehicle must be warmed to normal operating temperatures.</li><li>All implements should be removed from the vehicle prior to beginning the calibration process.</li><li>During the calibration process, have the vehicle’s engine set at normal operating speed or at least at a minimum of 1600 RPM.</li><li>The Auto Calibrate wizard takes a significant amount of space for the vehicle to operate within. Depending upon the vehicle size and type it may take at minimum approximately 300 x 700 ft (90 x 200 m) to complete the Auto Calibrate procedure.</li><li>The vehicle automatically executes a series of maneuvers during the calibration process including turning full left and full right. The calibration trajectory depends on vehicle type, controller and other differences in the vehicle. Always be prepared to take steering over manually if the vehicle drives towards an obstacle.</li><li>The field used for calibration must be dry (no water, snow or mud) and should be flat.</li><li>It is critical to have the best possible GPS/GNSS position quality for successful calibration. Before starting calibration verify the GPS uses the maximum number of available satellites and the augmentation system (ex. RTK, DGPS) is operating.</li><li>For the best results, it is recommended to drive vehicle forward for at least 60 meters (200 feet) with speed at least 6 km/h (4 mph) to establish good GPS heading before calibration.</li></ul><span>The calibration process comprises two main procedures:</span><ul><li><b>Common Calibration Steps</b> – These are the steps that all vehicles must perform during the Auto Calibrate process. These steps are also performed on vehicles that have been imported.</li><li><b>Vehicle Controller Type Specific Calibration Steps</b> – After the <b>Common Calibration Steps</b> have been completed, the Auto Calibrate continues to different steps depending on which vehicle type has been selected. The calibration routine for Valve / Steer-by-Wire, Mechanical Steering Unit / MDU-G4, and CAN Bus / ISOBUS Controllers are different.</li></ul></div>

<div> <h2>How to check if my tractor is compatible with an autosteer?</h2> <span>We have autosteer kits for many different tractor models and successful installation on tractors of 30-year-olds and even older.</span> <h2>Can I change the automatic steering system between tractors?</h2> <span>Yes, it is possible to change one system between multiple tractors. For this, you will need an additional switch kit for every tractor. The cost of the switch kit is 500 euro.</span> <h2>Whats the difference between Autosteer Kit and Autosteer system?</h2> <span>Major differences are in package parts.</span> <span><b>Autosteer Kit include:</b></span> <ul> <li>MDU-64</li><li>ECU-S1 controller<br/> (To this set we offer suitable RS 232 cable) </li></ul> <span><b>Autosteer System include:</b></span> <ul> <li>FieldBee Tractor GPS Navigation App;</li><li>FieldBee RTK GNSS Receiver ( L1 or L2 );</li><li>FieldBee RTK GNSS Base Station (L1 or L2 );</li><li>FieldBee Autosteer Kit.</li></ul></div>

<div><h2>What is an ECU?</h2><p><span>The ECU-S1 is a high precision electronic controller that provides automatic steering capability to the vehicle. The ECU-S1 controller receives guidance information from the Display device and sends steering commands to the vehicle. This </span><span>Operator’s Manual </span><span>provides information on how to setup, configure, and manage the various settings on the ECU-S1 controller and how to navigate through the software menus.</span></p><p><span>The ECU-S1 (the brain of the system) controller is compatible with multiple Displays. Please refer to the </span><span>Display Operator’s Manual </span><span>or contact your AutoSteer dealer for specific instructions on how to connect the ECU-S1 system components to the Display. Also refer to the </span><span>Display Operator’s Manual </span><span>for information on how to access ECU-S1 software menus and options. For information about setting up farms, fields, jobs, guidance patterns, and other Display related functions, please refer to your </span><span>Display Operator’s Manual</span><span>.</span></p><p><span>The ECU-S1 can be installed easily on most agricultural vehicle makes and models. This chapter provides basic information on how the ECU-S1 system components are organized and installed. Refer to the </span><span>Installation Manual </span><span>that comes with the vehicle installation kit for more details on the complete installation of the ECU-S1 system.</span></p><Image width='980' height='980' src='https://www.fieldbee.com/wp-content/uploads/2020/07/ECU-1-1024x1024.png' alt='ECU-1'/><h3>Features</h3><p><span>The ECU-S1 system is designed to be compatible with many makes and models of vehicles available in today’s agricultural market. The ECU-S1 can be installed on most agricultural platforms including articulated tractors, combines, MFWDs and standard front axle tractors, floaters, sprayers, swathers, track tractors, and others from most manufacturers including AGCO, Ag Chem, Case, Challenger, Fendt, John Deere, New Holland, Massey Ferguson, and many others. The same operator interface can be used on all vehicles, regardless of the make or model, making it easy for drivers to become familiar with the controls even if the system is installed on multiple vehicle types.</span></p><h3>ECU-S1 features include:</h3><ul><li><span>Automatic precision steering for agriculture vehicles;</span></li><li><span>Support for most vehicle controller types: mechanical, hydraulic, steer-by-wire, factory steer ready, and ISO-Bus (CAN);</span></li><li><span>Support for various Displays including consumer tablets and laptops;</span></li><li><span>Support for Ethernet wired or WiFi wireless connection to the Display;</span></li><li><span>Support for various GPS/GNSS receivers that provide NMEA messages;</span></li><li><span>High level of accuracy with cm-level (sub-inch) repeatability with compatible GNSS RTK receivers;</span></li><li><span>High precision 9-axis inertial sensors to provide enhanced terrain compensation and high accuracy.</span></li></ul></div>

<div><h2>What is the price of an automatic steering system?</h2><span>The price depends on the tractor model and the type of installation. The system has built-in terrain compensation and will provide very high repeatable accuracy of up to +/-1 cm. You can request the offer for the autosteer <a href='/contact-us'>here</a>.</span><h2>What exactly does your standard autosteer offer include?</h2><span>The standard package consists of:</span><ul><li>FieldBee Tractor GPS navigation app for 1 year.</li><li>FieldBee RTK GNSS receiver (L1 or L2);</li><li>FieldBee Autosteer kit;</li></ul><span>This can be extended with special kits depending on the tractor brand and an RTK base station.</span><h2>How does the antenna connect to the automatic steering system?</h2><span>Antenna connect to Autosteer system via cable. Watch the video about autosteer system:</span><iframe loading='lazy' src='https://www.youtube.com/embed/8fnOglpUeIg' width='600' height='400' frameBorder='0' allowFullScreen='allowfullscreen'></iframe><h2>What is a difference between Autosteer Kit and Autosteer system?</h2><span>Major differences are in package parts. </span><h3>Autosteer Kit include:</h3><ul><li>MDU-64</li><li>ECU-S1 controller</li></ul><span>(To this set we offer suitable RS 232 cable)</span><h3>Autosteer System include:</h3><ul><li>FieldBee Tractor GPS Navigation App;</li><li>FieldBee RTK GNSS Receiver ( L1 or L2 );</li><li>FieldBee RTK GNSS Base Station (L1 or L2 );</li><li>FIeldBee Autosteer Kit.</li></ul></div>

<div><h2>Standard Tools Requirements</h2><span>The installer is assumed to have a complete set of common installation tools including:</span><ul><li>#2 Phillips screwdriver</li><li>5/32” Allen key</li><li>1/4” open wrench</li><li>1/4″ wrench</li><li>Torque wrench 0 to 20 lbf.in (0 to 2 N.m), for 5/32” hex bit</li></ul><h2>Vehicle Requirements</h2><span>Before installing the MDU-G4 system, verify the following items on the vehicle:</span><ul><li>The vehicle’s steering system is in good working order. Drive the vehicle to verify this prior to beginning the installation. There should be no play in the steering and the vehicle should turn proportionally the same to the left and right.</li><li>The vehicle’s electrical system and battery must be in good working order.</li><li>The vehicle should be fully cleaned before installing the MDU-G4 system. A clean vehicle will improve the overall installation and cable routing</li></ul><span>If any issues are discovered with the vehicle, they must be repaired prior to beginning the MDU-G4 installation by a qualified service person for the vehicle.</span><span><b>Note:</b> This installation manual, vehicle specific installation manuals, and sub-kit manuals contain valuable information for servicing the MDU-G4 system. After the installation is complete, store all these manuals in a safe place for future reference.</span><h2>Vehicle Inspection</h2><span>Before installing the MDU-G4 system, confirm that the vehicle and the vehicle’s steering system are in good working order by driving it around. In addition, verify the following items:</span><ul><li>Verify that you can turn the steered wheels from lock to lock.</li><li>Record the time it takes to turn the vehicle’s steering mechanism (ex. steering axle, articulation point) from full left to full right and then record the time to go from full right to full left as fast as you can manually. This will be used later to ensure steering performance is okay.</li><li>Verify the vehicle steers straight and does not pull to one side when driving in a straight line.</li><li>Verify that there are no oil leaks.</li><li>Check for loose or worn steering components.</li></ul><span>If any part of the vehicle is not in working order, have the system serviced by a qualified technician prior to beginning the MDU-G4 installation procedure.</span><h2>How to install an auto steer?</h2><ol><li>Take an MDU – mechanical drive units. The installation of MDU takes a fixed part – Gear wheel, which needs to be installed under the steering system.</li><li>Attached to the steering wheel.</li><li>Tighten an anti rotation brackets. Once you made the installation, connect the MDU to it.</li><li>Connect the cable</li><li>Enjoy your ride as other clients:</li></ol><iframe width='560' height='315' src='https://www.youtube.com/embed/4nakth6Xiwg' title='YouTube video player' frameborder='0' allow='accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture; web-share' allowfullscreen></iframe><span>Watch the video for broader understanding (at John Deer 6020).</span><iframe width='560' height='315' src='https://www.youtube.com/embed/8fnOglpUeIg' title='YouTube video player' frameborder='0' allow='accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture; web-share' allowfullscreen></iframe><h2>Can you provide an auto steer installation service?</h2><span>We provide installation service by partners in Germany, Belgium, Austria, the Netherlands and Ukraine. In other countries, service brings by local specialists with experience of installation auto steering systems by Claas, Mueller-Electronics, Ag Leader, TeeJet.</span><ReadMore link={'/b2b'}>Become a partner</ReadMore><h2>Do I need to order additional cables?</h2><span>We offer a full package for your autosteer/autosteer kit, so you do not need to order additional cables.</span><h2>Which time it takes to install the auto steer kit by my own?</h2><span>Installation time depends on your tech level. It may take several hours. We highly recommend to go briefly through <a href='https://drive.google.com/file/d/1u9AuKSX_JZM6mGaxnDN3AzwPt08M-smr/view' target='_blank'>manual</a>.</span><h2>How to connect L1/L2 receiver</h2><span>The ECU-S1 requires the position information from an external RTK GNSS receiver. The receiver providing NMEA messages can be directly connected to the ECU-S1 over the RS-232 Serial interface.</span><span>The minimum RTK GNSS receiver configuration requirements are as follows:</span><ul><li>38400 bps baud rate; 115200 is recommended;</li><li>GGA NMEA messages at 10 Hz;</li><li>VTG NMEA messages at 10 Hz;</li><li>ZDA NMEA messages at 1 Hz;</li><li>Position data resolution must have at least 6 decimal places; 8 places are recommended;</li><li>RTK, DGPS, OmniSTAR™ or other correction mode improving position quality is highly recommended.</li></ul><span>If you have FieldBee L1/L2 RTK receiver you can find the installation guide <a href='https://drive.google.com/file/d/1m3q3XuaP762VVlcZE1QzJpyBtxAw6xTf/view'>here</a></span><h2>Figure 1-6 L1/L2 RTK GNSS receiver  Connections</h2><img width='656' height='404' src='https://www.fieldbee.com/wp-content/uploads/2020/07/ecu.png' alt='ecu'/><span><i>Figure 1-6</i> shows L1/L2 RTK GNSS receiver connection. Diagram shows the receiver connected directly to ECU-S1.</span></div>

<div><h2>What is a MDU?</h2><span>The MDU-G4 mechanical drive unit is a high-performance steering actuator designed to provide high precision steering when coupled to a GPS automated steering system. The MDU-G4 was designed for ease of installation, portability between vehicles and a long service life. The MDU-G4 uses a reliable high torque DC motor and a robust and simple gear drive for fast and responsive steering under all field steering conditions. The unique split gear design and quick-release latch makes for an easy installation that does not require the removal of the steering wheel so you gain time and are also able to easily transfer your MDU-G4 between many.</span><span>This <a href='https://drive.google.com/file/d/1IRU1GS1N093YZ7uiBBYth4T9ntDEJ0kr/view' target='_blank'>manual</a> provides the basic information and overview of the installation procedure for installing the MDU-G4 steering actuator on a vehicle. The MDU-G4 can be installed on many makes, models, and types of vehicles. Read this manual prior to beginning the installation as this manual provides the cautions and warnings that need to be recognized and understood prior to installing or operating an MDU-G4 system.</span><span>This manual provides the instructions for the installation of the components that come with this MDU-G4 installation kit. The installation is broken down into specific sections that may refer to sub-kit assemblies that are part of this kit. These sub-kits will come with their own instructions so refer to those when directed for information on installing the sub-kit parts.</span><span>Prior to operating and installing the MDU-G4 system, be sure to read and understand the Steering Controller Operator’s Manual that comes with the Steering Controller system. That manual provides the instructions on how to operate the MDU-G4 system as well additional safety information.</span><Image width='514' height='384' src='https://www.fieldbee.com/wp-content/uploads/2020/07/MDU.png' alt='MDU'/><h2>Before installing the MDU-G4 system, verify the following items on the vehicle:</h2><ul><li>The vehicle’s steering system is in good working order. Drive the vehicle to verify this prior to beginning the installation. There should be no play in the steering and the vehicle should turn proportionally the same to the left and right.</li><li>The vehicle’s electrical system and battery must be in good working order.</li><li>The vehicle should be fully cleaned before installing the MDU-G4 system. A clean vehicle will improve the overall installation and cable routing</li></ul><span>If any issues are discovered with the vehicle, they must be repaired prior to beginning the MDU-G4 installation by a qualified service person for the vehicle.</span></div>

<div><h2>I need submeter accuracy, which system should I choose?</h2><span>Our FieldBee antenna as a stand-alone device provides submeter accuracy. It means that the accuracy of the system will be below 1 meter and approximately 20-50 cm pass-to-pass.</span><span>The system can be used for tracking and performing operations that do not require high accuracy, for example spraying, or parallel driving with wide implements.</span><span>The FieldBee antenna is easy-to-use, works on batteries and doesn’t require any installation on your tractor. You can find more information about the system <a href='https://www.fieldbee.com/product/fieldbee-rtk-base-station/?utm_source=kb&utm_medium=refferal&utm_campaign=article' target='_blank'>here</a>.</span><h2>What level of accuracy do I need?</h2><span>From the experience of our customers, submeter accuracy of the system (30-50 cm) can be already helpful to work on spraying operations without tramlines, to achieve minimal overlap between passes. It already allows you to work in fog and at night but can not be used for operations that require higher precision such as seeding.</span><span>When choosing a smart antenna it is advisable to choose the one that can be later upgraded to the higher centimetre accuracy through additional purchase of RTK base station or connection to a local NTRIP provider.</span><span>Otherwise, its usage will be very limited for only certain operations and highly likely will not meet all your future needs.</span><span>Some field operations do not require high accuracy, for example, spraying, or parallel driving with wide implements. In this case, a system that provides submeter accuracy is sufficient.</span><span>But if you would like to have a system that can be used for all types of operations then we recommend you to go for the system with maximum accuracy.</span><h2>I need RTK accuracy, which system should I choose?</h2><span>You can use the FieldBee antenna in combination with the RTK base station which improves the accuracy of the FieldBee to +-1 cm.</span><span>You can also connect the FieldBee to an RTK correction network that is available in your areas such as SAPOS (Germany), FLEPOS (Belgium), MoveRTK (Netherlands) and others.</span></div>

<div><h2>How to choose a tractor navigation system?</h2><span>The best way to choose the right tractor navigation system is to contact us and get a personalized solution. Our precision farming experts knows the best product for your machinery and type of fieldwork.</span><span>FieldBee offers for you to choose the right tractor navigation system, which will make your farmer’s life easier. You can with no doubt find the best GPS device, which helps to get absolute accuracy on your farm.</span><span>Before that, we want to share with articles, which should help you with picking the right product for your farm needs.</span><ul><li><a href='https://www.fieldbee.com/blog/guide-on-how-to-choose-the-best-tractor-gps/' target='_blank'>Guide On How To Choose The Best Tractor GPS</a></li><li><a href='https://www.fieldbee.com/blog/rtk-modes-for-farm-gps-system/' target='_blank'>RTK Modes For Farm GPS System</a></li><li><a href='https://www.fieldbee.com/blog/hydraulic-autosteer-vs-mechanic/' target='_blank'>Hydraulic Autosteer Vs Mechanic</a></li></ul></div>

<div><h2>How to choose the right receiver?</h2><span>We offer FieldBee L1 and L2 RTK receivers. </span><span><b>FieldBee L1</b> is recommended for farmers that have flat fields without high trees, buildings and power lines or those who do not require high precision and will be satisfied with 30-50 cm accuracy in DGPS mode (without connection to RTK signal). With a connection to the RTK signal, you can achieve up to +-2 cm accuracy.</span><span><b>FieldBee L2 RTK receiver</b> is ideal for farmers that require very high precision and their fields have hills and obstacles for RTK signal. With a connection to the RTK signal, you can achieve up to +-1 cm accuracy.</span><h2>What the difference between L1 and L2?</h2><span>Difference between L1 and L2 Receiver mostly focused in:</span><ul><li>Accuracy as standalone device/RTK correction</li><li>Range of receiving correction</li><li>Time to receive/recover RTK signal</li></ul><span>For more details, please, check the provided image:</span><Image src='https://www.fieldbee.com/wp-content/uploads/2023/04/Screen-Shot-2023-05-11-at-10.03-1024x902.png' alt='Difference between L1 and L2 Receiver' width='980' height='863'/></div>

<div><h2>How to connect L1 receiver to NTRIP</h2><span>FieldBee GNSS receiver can provide 0 – 4 cm accuracy with connection to local NTRIP provider. There are a few required conditions for that. FieldBee GNSS receiver needs to:</span><ul><li>Receive a signal from more than 8 satellites;</li><li>Be connected to the Internet (WiFi network or Hotspot network);</li><li>Be set up to the active account at the local NTRIP provider.</li></ul><blockquote><b>Info!</b> You can connect FieldBee receiver to any 2,4 GHz WiFi network or mobile Hotspot, enabled from a device which is not using for FieldBee setup. 5G networks are not available for RTK correction reception.</blockquote><span>Start initial set up by locating FieldBee GNSS receiver at 1-1,5 m height above the ground and wide-open area. Download FieldBee toolbox from Play Store, following the <a href='https://play.google.com/store/apps/details?id=com.kmware.efarmer' target='_blank'>link</a></span><ol><li>Turn FieldBee receiver on;</li><li>Open FieldBee toolbox app;</li><li>Choose FieldBee;</li><li>Tap FieldBee serial number to continue setup;</li><li>Connect FieldBee GNSS receiver to the internet:</li><li>Setup NTRIP connection:<ol><li>Tap Connect to NTRIP Network.</li><li>Tap Add NTRIP network button.</li><li>Input: server, port, choose available mountpoint*, login, and password;</li><li>Tap Connect button.</li><li>NTRIP profile is added to list successfully.</li><li>Tap the NTRIP profile to apply these settings.</li><li>NTRIP profile has been applied.</li><li>Wait until FieldBee receiver will be connected to NTRIP network.</li></ol></li></ol><Image src='https://www.fieldbee.com/wp-content/uploads/2020/07/l1-ntrip-connection-flow-1-scaled.jpg' alt='l1-ntrip-connection-flow-1' width='2560' height='1476' /><Image src='https://www.fieldbee.com/wp-content/uploads/2020/07/l1-ntrip-connection-flow-2-scaled.jpg' alt='l1-ntrip-connection-flow-1' width='2560' height='1476' /><Image src='https://www.fieldbee.com/wp-content/uploads/2020/07/l1-ntrip-connection-flow-3-scaled.jpg' alt='l1-ntrip-connection-flow-1' width='2560' height='1476' /></div>

<div><h2>Can I use one system for different machines?</h2><span>Yes, that is possible, you will need to purchase an additional switch kit for each machine. Our sales can advise you on the costs.</span><span><p>Contact us for details:</p><p>Email: <a href='mailto:sales@fieldbee.com'>sales@fieldbee.com</a></p><p>Phone: <a href='tel:+49 2651 95 29 735'>+49 2651 95 29 735</a></p></span><h2>How to check if my tractor is compatible with an autosteer?</h2><span>We have autosteer kits for many different tractor models and successful installation on tractors of 30-year-olds and even older.</span><span>You can send us information about your tractor, by filling out the form below and we will check whether we can offer a kit for you.</span></div>

<div><h2>Do you have a representative in my area?</h2><span>Yes, we have dealers in Europe, North America, Asia, and Africa.</span><span>If we don’t have a partner in your country you can <a href='/contact-us'>contact our global sales team</a>.</span></div>

<div><h2>Do you ship internationally? What are the shipping costs?</h2><span>Yes! We ship all over the world.</span><span>Delivery of FieldBee receivers is free within the EU.</span><span>Delivery to other countries outside the EU is not included in the price. You can find out the shipping costs by writing us an email <a href='mailto:info@fieldbee.com'>info@fieldbee.com</a></span><h2>Can I return the products?</h2><span>Yes, you have 30 days money back guarantee and for that period of time we are in charge of taking the product back.</span><span><b>We also provide 2 years warranty on our products.</b></span></div>

<div><h2>How to choose the right receiver?</h2><span>Before making the final decision, you need to know which RTK GNSS receiver suits you the most. We offer you 2 options: FieldBee L1 and L2 RTK receivers. What is the main difference? Please, read below.</span><span><b>FieldBee L1</b> is recommended for farmers that have flat fields without high trees, buildings and power lines or those who do not require high precision and will be satisfied with 30-50 cm accuracy in DGPS mode (without connection to RTK signal). With a connection to the RTK signal, you can achieve up to +/-2 cm accuracy. More about FieldBee L1 RTK GNSS receiver: <a href='/products/rtk-l2-receiver' target='_blank'>https://www.fieldbee.com/products/rtk-l2-receiver/</a></span><span><b>FieldBee L2 RTK receiver</b> is ideal for farmers that require very high precision and their fields have hills and obstacles for RTK signal. With a connection to the RTK signal, you can achieve up to +/-1 cm accuracy.</span><span><p>You can find a comparison of those two receivers <a href='https://www.fieldbee.com/blog/new-fieldbee-rtk-l2-receiver-one-antenna-that-suits-all-farmer-needs/?utm_source=kb&utm_medium=refferal&utm_campaign=article' target='_blank'>here</a>.</p><p>And read more <a href='/products/rtk-l2-receiver/?utm_source=kb&utm_medium=refferal&utm_campaign=article/'>details</a> about L2 receiver.</p></span></div>

<div><h2>What is the price of an automatic steering system?</h2><span>The price is starting from 4999 Euro. It depends on the tractor model and the type of installation. The system has built-in terrain compensation and will provide very high repeatable accuracy of up to ±2,5 cm.</span></div>

<div><Image src='https://lh6.googleusercontent.com/bTHaLezTvQyyC8iir3H5kv8fvC3yj9RndKGtvWB8Dlbt19VAVWnOXuylQdYqY1JstxAP0UneN2IzWNW_g9j-XRCl9bsvvtiUJAzDXR0x9wv7hS2zFSldOp6I50En_y2nAhgyU9M1DG-sst5yANZtXdsZSqvx4sGXGmJJsW8h69PZ9X2aAb9eOmkZ5-9zlw' width='142' height='140' alt='efarmer'/><span> Thank you for your purchase. We want you to be completely happy with your FieldBee product.</span><span> If, however, you are not completely satisfied with your purchase for any reason, you can return it within 30 days of the receiving date and get a full refund.</span><span>Please see below for more information on our return policy.</span><h3>How to return products</h3><span> To initiate a return of your order, you must contact the support team. The returned parcel needs to be shipped within 30 days from the date of its arrival at your doorstep.</span><span>Please follow the below checklist:</span><ul> <li> Please contact the Support team to get your Return Authorization number. </li><li> All returned items must be returned in the <b style='display: inline-block'>original packaging</b>, including all accessories, documentation and packaging materials. Boxed items can be opened, but all the accessories must be included. </li><li> The returned products have to be in an “as new” condition <ul> <li> New products may have installation marks (screw impressions, etc.) or other light marks. </li><li> Used products: if the product you bought from us was 'as new' or 'refurbished', it needs to be in the same condition as you received it from us and may also include installation marks (screw impressions, etc.) or other light blemishes. </li></ul> </li><li> Pack the products properly, preferably using the original packing and wrapping materials that your product came with when returning your package to us. </li></ul><span> If your package was originally shipped double-boxed, please return the unit(s) double-boxed so they arrive safely at our facility.</span><h3>Proper returns: Wrapping materials used</h3><Image width={480} height={320} src='https://www.fieldbee.com/wp-content/uploads/2022/11/unnamed.jpg' alt='Wrapping materials used' style='border-radius: 10px'/><h3>Improper returns: Original packaging is missing</h3><Image width={512} height={512} src='https://www.fieldbee.com/wp-content/uploads/2022/11/unпnamed.jpg' alt='Original packaging is missing' style='border-radius: 10px'/><h3>Proper returns: Double-boxed, wrapping materials used</h3><Image width={512} height={384} src='https://www.fieldbee.com/wp-content/uploads/2022/11/unnamааed.jpg' alt='Double-boxed, wrapping materials used' style='border-radius: 10px'/><ul> <li> <span>Shipping label:</span><span> Use the following <b style='display: inline-block'>shipping address</b>: <br/> FieldBee Polska <br/> Bojkowska 53, <br/> 44-100 Gliwice <br/> Poland </span><span> Contact person: <br/> <b style='display: inline-block'>Alena Tsymbaliuk</b> <br/> <a href='mailto:alena.tsymbaliuk@fieldbee.com'> alena.tsymbaliuk@fieldbee.com </a> <br/> <a href='tel:+48600479989'>+48600479989</a> </span></li><li> Please write the RA number on the shipping label and NOT on the product box itself; </li><li>Please use a shipping method that is traceable;</li><li> We recommend that you insure your package when shipping it back to us. We assume responsibility for the products only after we receive them; </li><li> <span> Ship the product no longer than 30 days after receiving it. Otherwise, the right to a refund will be lost. </span><span> <b style='display: inline-block'> If you are located outside of the EU </b> you will also get a <b style='display: inline-block'> Commercial invoice for customs </b> </span></li><li> Fill in the required documentation (Commercial Invoice with your return authorization number included). Print 3 copies of the Commercial Invoice. </li><li> Properly pack all items to be returned (see instructions above). </li><li> Attach the commercial invoice to a plastic document sleeve on the outside of our return package. This is necessary for your return to clear customs. </li><li> Follow any additional instructions provided via email along with the return shipping address. </li></ul><h3>Shipping costs</h3><span style='text-align: start'> Please note, <b style='display: inline-block'>customers are responsible</b> for all return shipping charges <b style='display: inline-block'>unless you’re returning</b> <b style='display: inline-block'> the product due to it being defective or </b> due to delivery of the wrong product.</span><h3>Defective Product and Returns Due to Our Error</h3><span> If there are mistakes with your order, or products arrive defective / damaged at the time of receipt, we’ll make it right by:</span><ul> <li> Sending you replacement parts or accessories (please contact our support team) </li><li>Replacing the product</li><li>Issuing a refund</li></ul><span>And we’ll also cover the costs of any return shipping.</span><span> If the return is <b style='display: inline-block'>not</b> due to our error or product defect, return shipping fees will apply.</span><h3>Refunds</h3><span> <b style='display: inline-block'>After we receive</b> your returned item and inspect its condition, we will process your refund or exchange.</span><span>Refunds will be sent to your original method of payment.</span><span> Please allow at least <b style='display: inline-block'>14 days from receipt of your item</b> to process your return.</span><span> We will notify you by email when your return has been processed.</span><span> In case products received are not in proper condition as defined above, the item's list price will be deducted from your refund partially or in full, according to the item's state.</span></div>

<div><h2>How to connect L1 via Toolbox?</h2><span><p>Start initial set up by locating FieldBee GNSS receiver at 1-1,5 m height above the ground and wide-open area.</p><p>Download FieldBee toolbox from Play Store, following the <a href='https://play.google.com/store/apps/details?id=com.kmware.efarmer'>link</a>.</p></span><ul><li>Turn FieldBee receiver on.</li><li>Open FieldBee toolbox app</li><li>Choose FieldBee;</li><li>Tap FieldBee serial number to continue setup;</li></ul><Image src='https://www.fieldbee.com/wp-content/uploads/2020/07/l1-connection-flow-1-scaled.jpg' alt='l1-connection-flow-1' width='2560' height='2211'/><span>Connect FieldBee GNSS receiver to the Internet. Connecting the receiver to an available WiFi network:</span><ul><li>tap WiFi connection;</li><li>tap one of available WiFi networks;</li><li>input password for this network;</li><li>tap Connect button;</li><li>*wait until FieldBee will become connected to WiFi network;</li><li>FieldBee is connected to the WiFi network.</li></ul><img src='https://www.fieldbee.com/wp-content/uploads/2020/07/l1-connection-flow-2-compressor-scaled.jpg' alt='l1-connection-flow-2' width='2560' height='1155'/><img src='https://www.fieldbee.com/wp-content/uploads/2020/07/l1-connection-flow-3-scaled.jpg' alt='l1-connection-flow-3' width='2560' height='1517'/></div>

<div><h2>How does the antenna connect to the smartphone/tablet?</h2><span>The FieldBee antenna connects to a smartphone/tablet via Bluetooth.</span><h2>How does the antenna connect to the automatic steering system?</h2><span>Via cable that goes together with the system. The work of autosteer system with completing shown here:</span><iframe loading='lazy' src='https://www.youtube.com/embed/8fnOglpUeIg' width='600' height='400' frameBorder='0' allowFullScreen='allowfullscreen'></iframe><h2>Which satellite signal does your antenna provide?</h2><span>FieldBee RTK GNSS L1 Receiver provides connection to the GPS, GLONASS and BeiDou signals.</span></div>

<div> <h2>How to connect FieldBee Receiver and Base station</h2> <span>Get to know how to connect FieldBee Base station and Receiver in the detailed description below or watch the video instead.</span> <iframe loading='lazy' src='https://www.youtube.com/embed/2lIZk__KxAY' width='600' height='400' frameBorder='0' allowFullScreen='allowfullscreen'></iframe> <span>Before starting, you need to know FieldBee Base station working mode is the absolute position and static mode gets absolute accuracy.</span> <h3>Let’s started:</h3> <ol> <li>Locate a spot where the base station will always stay</li><li>Put FieldBee receiver to this location</li><li>Open FieldBee Toolbox app</li><li>Tap on Location (coordinates will be copied to clipboard)</li><li>Locate FieldBee base station to the same spot where the receiver was</li><li>Connect to FieldBee Base Station with toolbox app</li><li>Open Base station position</li><li>Tap Add manually button</li><li>Input position name (e.g. “home”, “office”, “Field1”)</li><li>Tap Paste button to paste copied coordinates</li><li>Tap Save button; (coordinates are added to the Base station position list)</li><li>Tap created position and base station will apply Static mode with inputted coordinates</li><li>Restart base.</li></ol> <h3>How to link receiver and base station in WiFi working mode:</h3> <ol> <li>Open FieldBee toolbox app</li><li>Connect to the FieldBee receiver</li><li>Tap FieldBee base station</li><li>Tap Add new ‘Base’</li><li>Input Base station serial number</li><li>Tap Connect</li><li>The receiver is linked to Base station.</li></ol> <h3>Important:</h3> <ul> <li>Make sure to screw antenna onto the Base Station</li><li>Make sure you have signal at least from 8 satellites</li></ul> <h3>To start setting up the Base station and FieldBee receiver follow the next steps:</h3> <ol> <li>Locate Base Station and FieldBee receiver outside and place them at 1-1,5 m above ground level (on an open sky leaving at least 2 meters in between receiver and base station)</li><li>Make sure that external radio antennas have been screwed into FieldBee receiver and Base station</li><li>Turn on antennas.</li></ol> <span>Here are you go, FieldBee Base station and Receiver are connected now.</span> <h2>Setting up FieldBee RTK base station via Bluetooth</h2> <span>To start with, open the app, click on “GPS only” on the upper left corner of your device.</span> <span>Select “Other receivers” (an external GPS device that appears). Check the video to make sure you understand it properly.</span> <span>Your device must be connected to Bluetooth. For that:</span> <ul> <li>Open your device’s Setting app</li><li>Click on “Connections”</li><li>Check to see if Bluetooth is ‘on’</li></ul> <h2>How to connect FieldBee with SAPOS?</h2> <span>FieldBee works with SAPOS in Germany. You need to create an account there and it is necessary to be connected to Base station with transmitting correction using messages RTCM version 3 and higher.</span> <h2>Could you state the LoRa frequency?</h2> <span>The LoRa frequency is 868 MHz in Europe and 915 MHz in the United States.</span> <h2>How to connect FieldBee with FLEPOS</h2> <span>You can find a more detailed guide about receiving correction from FLEPOS via the <a href='https://www.fieldbee.com/wp-content/uploads/2020/07/Flepos-correction-NL-low.pdf'>link</a> (NL).</span> <h2>How to use Fieldbee with RTK correction providers?</h2> <span>FieldBee can receive RTK correction from networks that are available in your area.</span> <span>The accuracy of the system in such cases can be up to +/-1 cm.</span> <span>Correction networks typically have paid access, but in some countries and regions, they are provided for free by the government. For example FLEPOS network in Belgium, SAPOS in Germany, MoveRTK in the Netherlands etc.</span> <h2>Additional requirements</h2> <span>You will need to register with your local RTK correction provider (NTRIP provider) and obtain the following parameters needed for connection:</span> <ul> <li>Domain or IP address and port</li><li>Login and Password</li><li>Nearest mount point name or Correction stream name When asking the information above, tell your provider that RTCM 3.x format is required. (We do not support RTCM 2.x format).</li></ul> <blockquote><b>Important!</b> You will need to have a Wi-Fi access point with the Internet access or share Internet from your Android device by enabling mobile Hotspot in Android Settings.</blockquote></div>

<div> <h2>What else is required for the functioning of the system?</h2> <span>For the functioning of the system you will need:</span> <ul> <li>An android tablet/smartphone. Here is a <a href='https://www.fieldbee.com/wp-content/uploads/2021/06/Recommended-compatible-devices-2021.pdf'>list of recommended devices</a>.</li><li>Bluetooth should be enabled.</li><li>Registration with your local <b>NTRIP provider (if you use system with NTRIP)</b> and the following information: IP address, Port, Login and Password, Recommended Mount points (if you don’t have your own RTK Base station)</li></ul> <h2>Can I connect another antenna to the FieldBee RTK Base station?</h2> <span>To receive correction from FieldBee RTK Base station, the antenna needs to receive NMEA messages in RTCM x3 format, also receive GGA, VTG messages, update rate can be 5 or 10 Hz. For autosteer, it is needed to set up a baud rate for the 115200.</span> <h3>Possible connection:</h3> <ul> <li>GGA at 5Hz -yes</li><li>VTG at 5Hz – yes</li><li>GSA at 1Hz - yes</li><li>GSV at 1Hz – yes</li><li>GST at 1Hz – yes</li><li>ZDA at 1Hz – yes</li><li>Baud Rate of 115200 – yes</li></ul><span><b>The best way to know is to try it.</b></span></div>

<div> <h2>How to choose the right receiver?</h2> <span>We offer FieldBee L1 and L2 RTK receivers. </span> <span><b>FieldBee L1</b> is recommended for farmers that have flat fields without high trees, buildings and power lines or those who do not require high precision and will be satisfied with 30-50 cm accuracy in DGPS mode (without connection to RTK signal). With a connection to the RTK signal, you can achieve up to +-2 cm accuracy.</span> <span><b>FieldBee L2 RTK receiver</b> is ideal for farmers that require very high precision and their fields have hills and obstacles for RTK signal. With a connection to the RTK signal, you can achieve up to +-1 cm accuracy.</span> <span>You can find a comparison of those two receivers <a href='/products/rtk-l2-receiver/'>here</a>.</span> <span>And read <a href='/blog/new-fieldbee-rtk-l2-receiver-one-antenna-that-suits-all-farmer-needs/'>here</a> more detailed about L2 receiver</span> <h2>What the difference between L1 and L2</h2> <span>Difference between L1 and L2 Receiver mostly focused in:</span> <ul> <li>Accuracy as standalone device/RTK correction;</li><li>Range of receiving correction;</li><li>Time to receive/recover RTK signal.</li></ul> <span>For more details, please, check the provided image:</span> <Image src='https://www.fieldbee.com/wp-content/uploads/2020/07/Screen-Shot-2020-07-30-at-12.50.02-PM.png' alt='difference between L1 and L2' width='1446' height='1492'/> <span>What to choose FieldBee RTK GNSS L1 or L2 Receiver, read the <a href='/blog/new-fieldbee-rtk-l2-receiver-one-antenna-that-suits-all-farmer-needs/'>article</a>.</span></div>

<div> <h2>How to connect L2 receiver to NTRIP</h2> <span>Before starting, check if you have NTRIP provider in your country at the page: <a href='/info/ntrip/'>www.fieldbee.com/info/ntrip</a> or QR code:</span> <Image src='https://www.fieldbee.com/wp-content/uploads/2020/07/Screen-Shot-2020-07-06-at-1.07.22-PM.png' alt='qr' width='374' height='458'/> <blockquote><b>Important!</b> If you didn’t find your NTRIP provider in the list try to find it yourself. If you don’t have an NTRIP provider in your region – you can purchase a FieldBee RTK GNSS Base station, get high accuracy and share your signal with neighbours.</blockquote> <h3>Register with local NTRIP provider</h3> <span>Obtain the following information:</span> <ul> <li>IP address (ask for it specifically from NTRIP provider);</li><li>Port;</li><li>Login and Password;</li><li>Recommended mount points.</li></ul> <h3>Prepare WiFi access inside the tractor cabin</h3> <span>To receive RTK correction from a NTRIP provider for your FieldBee L2 receiver you’ll need to have a WiFi network in your tractor cabin.</span> <blockquote> <span>Important!</span> <ul> <li>Use rtkwifi and 12345678 as name and password for WiFi (rename Hotspot or use these credentials on WiFi router). FieldBee receiver will be connected to WiFi networks with this name automatically.</li><li>If you can not use rtkwifi and 12345678 as credentials for your WiFi network, first do additional Step 4 below <a href='https://drive.google.com/file/d/1A27A309UOT6r_FpQ7sLb9pwnZ9A9ZZ7k/view' target='_blank'>(See User Manual)</a>.</li></ul> </blockquote> <span>To enable Internet in your tractor cabin you have 2 options:</span> <ul> <li>Turn on WiFi Hotspot on your tablet/phone; If Hotspot is not active on your smartphone please contact your mobile network provider to enable this functionality. Incoming phone calls can disrupt Hotspot on you phone, if you get a lot of calls use next option;</li><li>Install in the cabin 3G/4G WiFi Router with a sim Card;</li></ul> <h3>Connect to NTRIP provider</h3> <ul> <li>Turn on FieldBee L2 receiver;</li><li>Open FieldBee L2 Toolbox app and press Allow to access your device location;</li><li>From the list of devices connect to L2 receiver with your Serial number;</li></ul> <blockquote><b>Important!</b> If you don’t see your antenna in the list, restart the antenna and application.</blockquote> <span> <ul> <li>Open NTRIP parameters and Paste credentials that you’ve received from your NTRIP provider (see step 1) and press SAVE;</li><li>Press REBOOT for applying parameters;</li><li>In L2 Toolbox app wait until NTRIP status has changed from Error to OK/Active;</li><li>Open FieldBee tractor navigation app and Start your work with high precision. Your accuracy should change to FRTK/RTK;</li></ul> </span> <span>For more details, go to <a href='https://drive.google.com/file/d/1A27A309UOT6r_FpQ7sLb9pwnZ9A9ZZ7k/view' target='_blank'>User Manual</a>.</span></div>

<div> <h2>How to connect L2 via Toolbox app?</h2> <span>Follow the steps to connect L2 via Toolbox:</span> <ol> <li>Open L2 ToolBox app, choose base station from the list of devices and click on WiFi parameters;</li><li>Fill in WiFi credentials of your WiFi network WiFi SSID (WiFi name) and WiFi password and press SAVE;</li><li>Press REBOOT for applying new parameters;</li><li>Open L2 ToolBox app again. Find a FieldBee L2 base station that is now connected to your WiFi network (it will be with a new IP address);</li><li>In L2 ToolBox app and repeat steps 6 and 7 from the Perform static test (see <a href='https://drive.google.com/file/d/1CKjZYFefUZdvEq8Jc22fNm3QvHDd-Oly/view' target='_blank'>User Manual</a>). Check Statuses.</li><li>We are done with the L2 base station connection. Now we will start setting up a FieldBee L2 receiver on your tractor.</li></ol> <blockquote> <span><b>Info!</b> Important:</span> <ul> <li>You can use home WiFi if it is strong enough. If it is not, you should use a WiFi repeater.</li><li>WiFi have to be only 2G (2,4 GHz);</li></ul> </blockquote> <span>For more questions about L2, check the <a href='https://drive.google.com/file/d/1CKjZYFefUZdvEq8Jc22fNm3QvHDd-Oly/view' target='_blank'>User Manual</a>.</span></div>

<div> <h2>How does the antenna connect to the smartphone/tablet?</h2> <span>The FieldBee antenna connects to an Android smartphone/tablet via WiFi or hotspot.</span> <h2>How does the antenna connect to the automatic steering system?</h2> <span>FieldBee L2 RTK GNSS receiver connects via RS-232 cable, which goes with the system. Detailed connection process shown on the video below:</span> <iframe loading='lazy' src='https://www.youtube.com/embed/8fnOglpUeIg' width='600' height='400' frameBorder='0' allowFullScreen='allowfullscreen'></iframe> <h2>Which satellite signal does your antenna provide?</h2> <span>FieldBee RTK GNSS L2 Receiver provides a connection to the GPS, GLONASS, BeiDou and Galileo signals.</span> <span>Visit <a href='https://www.fieldbee.com/wp-content/uploads/2020/10/FieldBee-L2-RTK-GNSS-receiver-Datasheet-26.10.20.pdf' target='_blank'>technical datasheet</a> to find out more details about L2.</span></div>

<div> <h2>How to connect FieldBee with SAPOS?</h2> <span>FieldBee works with SAPOS in Germany. You need to create an account there and it is necessary to be connected to Base station with transmitting correction using messages RTCM version 3 and higher.</span> <h2>How to use Fieldbee with RTK correction providers?</h2> <span>FieldBee can receive RTK correction from networks that are available in your area.</span> <span>The accuracy of the system in such cases can be up to +/-1 cm.</span> <span>Correction networks typically have paid access, but in some countries and regions, they are provided for free by the government. For example FLEPOS network in Belgium, SAPOS in Germany etc.</span> <h3>Additional requirements:</h3> <span>You will need to register with your local RTK correction provider (<a href='/info/ntrip/' target='_blank'>NTRIP provider list</a>) and obtain the following parameters needed for connection:</span> <ul> <li>Domain or IP address</li><li>Port</li><li>Login and Password</li><li>Nearest mount point name or Correction stream name When asking the information above, tell your provider that RTCM 3.x format is required. (We do not support RTCM 2.x format).</li></ul> <span><b>Important!</b> You will need to have a Wi-Fi access point with the Internet access or share Internet from your Android device by enabling mobile Hotspot in Android Settings.</span> <h2>Could you state the LoRa frequency?</h2> <span> <p>LoRa is not currently available in L2 devices</p><p>It will be available later with future firmware updates.</p></span> <h2>How to connect FieldBee with FLEPOS?</h2> <span>You can find a more detailed guide about receiving correction from FLEPOS via the <a href='https://www.fieldbee.com/wp-content/uploads/2020/07/Flepos-correction-NL-low.pdf' target='_blank'>link</a> (NL).</span></div>

<div> <h2>Can I connect another antenna to the FieldBee RTK Base station?</h2> <span>To receive correction from FieldBee RTK Base station, the antenna needs to receive NMEA messages in RTCM x3 format, also receive GGA, VTG messages, update rate can be 5 or 10 Hz. For autosteer, it is needed to set up a baud rate for the 115200.</span> <h3>Possible connection:</h3> <ul> <li>GGA at 5Hz - yes</li><li>VTG at 5Hz – yes</li><li>GSA at 1Hz -yes</li><li>GSV at 1Hz – yes</li><li>GST at 1Hz – yes</li><li>ZDA at 1Hz – yes</li><li>Baud Rate of 115200 – yes</li></ul> <span>The best way to know it is to try it.</span> <h2>L2 data sheet</h2> <span> <p>You can find Technical data sheet for RTK GNSS L2 receiver <a href='https://www.fieldbee.com/wp-content/uploads/2020/10/FieldBee-L2-RTK-GNSS-receiver-Datasheet-26.10.20.pdf' target='_blank'>here</a>.</p><p>For Base station find Technical data sheet <a href='https://www.fieldbee.com/wp-content/uploads/2020/10/FieldBee-L2-RTK-GNSS-Base-station-Datasheet-26.10.20.pdf' target='_blank'>here</a>.</p></span> <h2>What do I need for a functioning system?</h2> <span>For the functioning system you will need:</span> <ul> <li>An android tablet/smartphone. Here is a <a href='https://www.fieldbee.com/wp-content/uploads/2021/06/Recommended-compatible-devices-2021.pdf' target='_blank'>list of recommended devices</a>.</li><li>WiFi or a SIM card with the Internet</li><li>RTK login details of a third party (if you don’t have your own RTK Base station)</li></ul></div>

<div> <h2>How to check if my phone is compatible with the FieldBee app</h2> <span>To work with the FieldBee app, you will need an Android device with the following parameters:</span> <h3>Minimum:</h3> <ul> <li>Android: 7;</li><li>Processor: Qualcomm Snapdragon 632 MediaTek Helio P22</li><li>RAM: 4GB</li><li>3G (WCDMA/UMTS/HSPA); 4G (LTE)</li><li>Connectivity/Radios: WiFi or 3G/LTE, Bluetooth.</li></ul> <h3>Recommended</h3> <ul> <li>Android 9;</li><li>Processor: Qualcomm Snapdragon 845 MediaTek Helio X30</li><li>RAM: 8GB</li><li>3G (WCDMA/UMTS/HSPA); 4G (LTE)</li><li>Connectivity/Radios: WiFi or 3G/LTE, Bluetooth.</li></ul> <span>Here you can find a list of recommended devices and accessories <a href='https://www.fieldbee.com/wp-content/uploads/2021/06/Recommended-compatible-devices-2021.pdf' target='_blank'>compatible devices</a>.</span> <h2>Can I connect the FieldBee app to another antenna, terminal or other systems?</h2> <span>It is possible to connect to the FieldBee app any antenna that has Bluetooth interface and receive NMEA messages. For that, you need to have active Premium app subscription</span> <span>Although we can not guarantee the compatibility of your antenna with our application.</span> <span>The FieldBee antenna was designed specifically to work well with the FieldBee app. You can find more information <a href='https://www.fieldbee.com/products/gps-app-subscription' target='_blank'>here</a>.</span> <h2>Is it necessary to have a smartphone/tablet? Does another monitor work?</h2> <span>We highly recommend using the FieldBee app on your Android smartphone or tablet for Navigation. Those devices will help you to stay productive and omit additional trouble while you are driving in fields.</span></div>

<div> <h2>How to use Navigation functionality</h2> <iframe width='560' height='315' src='https://www.youtube.com/embed/2lIZk__KxAY' title='YouTube video player' frameBorder='0' allow='accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture; web-share' allowFullScreen></iframe> <h3>3 things to know before starting:</h3> <ol> <li>Your location in the centre is represented by the blue dot</li><li> The top right buttons provide different layers and measurement tools <ul> <li>The layers: shows different map type and displays your fields borders with/without the crop (due to enabling option);</li><li>The measurement tools allow you to measure distances with a ruler path;</li><li>The measurement allows you to measure surface area with ruler area: use the points in sequential order.</li></ul> </li><li>The Location button on the bottom left ALWAYS brings you back to your current location.</li></ol> <h3>How to start to use Navigation functionality:</h3> <span>Press the (+) button to start</span> <ol> <li>Start with Task → here you can select an existing operation from the list or create a new one.</li><li>Select Field → Using one of the four options</li><li>Select your vehicle → you can choose one from the list or add your own</li><li>GPS → shows the GPS source that you are using (if you are using the FieldBee receiver you can click on GPS CHANGE SOURCE)</li><li>By pressing AB Straight you can see all of the available patterns (it may vary of your app subscription type: free or premium)</li><li>The last thing you need to do is implement width;</li><li>Press the arrow button to start;</li></ol> <span>Now you are ready to drive! ?</span> <h2>How to use Record keeping functionality</h2> <span>You can use Record keeping functionality for:</span> <ul> <li>Tasks</li><li>Fields</li><li>Notes</li><li>Glossary</li></ul> <h3>Tasks</h3> <span>To create a new task:</span> <ol> <li>Press (+) to select a task</li><li>Select a field or import a new field</li><li>Press save</li><li>Edit → add notes, make comments about work</li><li>Press x to back out → AUTOMATICALLY SAVES</li></ol> <h3>Fields</h3> <span>Here how you can create, edit, and organize your farm fields</span> <ol> <li>Choose an existing field or make a new one by pressing (+);</li><li>Create your field and press save;</li><li>Edit – name, crop.</li></ol> <h3>Notes</h3> <span>Let’s start:</span> <ol> <li>Press the (+) button;</li><li>Select one: Note, Fixed point, obstacle;</li><li>Go to the field and place it where necessary, select next;</li><li>Edit the information;</li><li>Select Save at the top (check icon).</li></ol> <h3>Glossary</h3> <span>You can add important data to:</span> <ul> <li>Materials</li><li>Vehicles</li><li>Crops</li><li>Workers</li></ul> <span> <p>Press (+) to add one of the options;</p><p>Edit the information and press Save.</p></span> <h2>How to get fields into the app?</h2> <span>Measure and draw your fields with a smartphone or import SHP map files from your computer</span> <ul> <li>Press Add button to create a field</li><li>Select Draw</li><li>Tap the map to allocate the field boundary points</li><li>Press a point and drag the handle to adjust its position</li><li>Tap at the right top corner to save the boundary</li><li>Enter Field name</li><li>Save the field</li></ul> <h2>How to use Autosteer functionality</h2> <span>Check the video or read preliminary steps on how to use Autosteer:</span> <ol> <li>Turn on ECU;</li><li>Wait until it will become ready for connection;</li><li>Open the app;</li><li>Go to settings;</li><li>Enable autosteer;</li><li>Choose WiFi → to go to ECU;</li><li>Return to Navigation;</li><li>Go to GPS Source → ECU.</li></ol> <span><b>Note:</b> The <b>Black button</b> enables auto steer. The <b>Red button</b> stops auto steer. <b>Important:</b> Galileo support will be included and set up only with the app software update in the future with improvement for antenna works. For now, there is no need for hardware upgrades.</span></div>

<div> <h2>How to change the language in the app?</h2> <span>When you open the FieldBee app, you need to go to the Menu (top left icon) -> Settings → Language and change it.</span> <span>From the <b>version 6.4.0</b> you have opportunity to choose the language immediately after launching the application.</span> <h2>How can I update the app to the latest version?</h2> <span>To update the <a href='https://play.google.com/store/apps/details?id=com.kmware.efarmer&amp;hl=ukhttps%3A%2F%2Fplay.google.com%2Fstore%2Fapps%2Fdetails%3Fid%3Dcom.kmware.efarmer&amp;hl=uk&amp;utm_source=kb&amp;utm_medium=refferal&amp;utm_campaign=app' target='_blank'>FieldBee app</a> to the latest version, please, go to Play market, open FieldBee app and press the 'Update' button.</span> <span> <p><i>Is it possible to receive both raw measurements and RTK corrected coordinates?</i></p><p>Yes, it is. Raw data (or NMEA messages) save at your device in log files</p></span> <h2>Is the data I saved during the trial period available after buying a subscription?</h2> <span>Yes, you can access the data you saved during the FieldBee trial period after buying the <a href='https://www.fieldbee.com/products/gps-app-subscription/?utm_source=kb&amp;utm_medium=refferal&amp;utm_campaign=article' target='_blank'>Premium subscription</a> for the app.</span> <h2>Does application work in offline mode?</h2> <span>Yes, you may use the FieldBee app offline while you are driving in the fields. All your tracks are saved to the device and will be synced after getting Internet access.</span> <span>FieldBee app needs Internet connection only for data synchronization (<b>Sign In, Sign Up and saving tracks to the cloud storage</b>)</span> <h2>Can I import/export files into the app?</h2> <span>Yes, you can import SHP map files in our <a href='https://app.efarmer.mobi' target='_blank'>Web app</a>.</span></div>

<div> <h2>Do you have iOS version?</h2> <span>The FieldBee app is available for Android users. If we start to develop the FieldBee app for iOS users, we will let you know!</span> <span>Stay in touch with us to get the news first.</span> <span>We recommend to buy inexpensive Android tablet for work and enjoy the GPS tractor navigation app. Otherwise you can check for a new <a href='https://www.fieldbee.com/wp-content/uploads/2021/06/Recommended-compatible-devices-2021.pdf' target='_blank'>affordable Android</a> device that can survive field work in your tractor.</span></div>

<div> <h2>I haven’t received a license (subscription) key</h2> <span>You receive a licence key automatically via email after we process the payment.</span> <span> <p>If you haven’t received a subscription key in 1-2 days, please contact our support team:</p><p>Email: <a href='mailto:support@fieldbee.com' target='_blank'>support@fieldbee.com</a></p><p>Phones: <a href='tel:+31628328900' target='_blank'>+31 62 832 89 00</a> (office), <a href='https://web.whatsapp.com/send?phone=+380502248722' target='_blank'>+38 050 224 87 22</a> (support in Whatsapp)</p></span> <h2>I would like to renew my subscription</h2> <span>If you would like to continue using FieldBee app you can <a href='/de/app'>pay for the new licence</a> on our website.</span> <h2>Where should I fill in the subscription key</h2> <span>Follow installation directions to find out how to fill in the subscription key.</span> <span>To install the app you should go through the following steps:</span> <ul> <li>Find the FieldBee app in Google Play or click <a href='https://play.google.com/store/apps/details?id=com.kmware.efarmer&amp;hl=uk&amp;utm_source=kb&amp;utm_medium=refferal&amp;utm_campaign=app' target='_blank'>here</a><Image src='https://www.fieldbee.com/wp-content/uploads/2020/07/Install-app-compressor.png' alt='Install-app-compressor' width='3708' height='3524'/></li><li>To fill in your license key follow these steps: <img src='https://www.fieldbee.com/wp-content/uploads/2020/07/Fill-in-license-key-compressor.png' alt='Fill-in-license-key-compressor' width='7088' height='3524'/></li></ul> <h2>What does an annual license for FieldBee app mean?</h2> <span>We offer 2 types of <a href='/de/app' target='_blank'>subscription</a>:</span> <ul> <li>Yearly subscription with 119 Euro per year</li><li>4-year subscription at 349 Euro (1 year is Free)</li></ul> <span>We charge annual subscription to be able to provide you with:</span> <ul> <li>app stability</li><li>free support</li><li>free regular updates</li><li>Improvements in current functionality</li><li>new features development</li></ul> <span>You can find more information <a href='/de/app'>here</a>.</span></div>

<div> <h2>How to connect to external GPS receiver?</h2> <span>To connect to FieldBee:</span> <ul> <li>Open the app</li><li>Click on “GPS only” on the upper left corner of your device.</li><li>Select “Other receivers” (an external GPS device that appears)</li></ul> <h3>Important requirements:</h3> <ul> <li>Turn on the Bluetooth (minimum battery has to be 10%)</li><li>To connect to the FieldBee app, the antenna needs to have Bluetooth interface and be able to receive NMEA messages</li><li>GPS has to be greater than 1 meter</li></ul> <span>Detailed instruction is shown here as well as a video guide:</span> <iframe loading='lazy' src='https://www.youtube.com/embed/PbyK6l5gYe8' width='600' height='400' frameBorder='0' allowFullScreen='allowfullscreen'></iframe></div>

<div> <h2>Which is the latest version of FieldBee app? How can I see which version am I using?</h2> <span>The latest version of FieldBee app you can check <a href='https://play.google.com/store/apps/details?id=com.kmware.efarmer&hl=en' target='_blank'>here</a>.</span> <span>Check the latest updates here. Open the FieldBee app and go to <b>Settings</b> to see what is the version you installed. Or do long tap on the app icon -> App info -> Advanced -> Scroll to the bottom you’ll see the app version.</span></div>

<div> <h2>How to use the Web app</h2> <span>Go to Web app <a href='https://app.fieldbee.com/' target='_blank'>here</a>.</span> <span>First of all, you need to <b>Sign up using the same login and password as in <a href='https://play.google.com/store/apps/details?id=com.kmware.efarmer' target='_blank'>FieldBee navigation app</a></b>. Read the detailed description below or check the video:</span> <iframe loading='lazy' src='https://www.youtube.com/embed/X5PdyPVAwWY' width='600' height='400' frameBorder='0' allowFullScreen='allowfullscreen'></iframe> <span>You get access to:</span> <ul> <li>Map — to see fields, tasks, and notes on the map</li><li>Task — to set and check task status</li><li>Field — to check how your fields are organized (easy to access and update data)</li><li>Glossary — to add data about materials, machinery, crops and coworkers.</li></ul> <span>Press (+) to import/add important information and press 'Save'.</span></div>

<div> <h2>Welcome you! Here you may find manuals of FieldBee mobile and web applications:</h2> <span> <ul> <li><a href='https://www.fieldbee.com/wp-content/uploads/2022/02/V.7.7.0_1v_FieldBee-tractor-navigation-Android-Application-User-Manual.-.pdf' target='_blank'>FieldBee tractor GPS navigation app v.7.7.0</a></li><li><a href='https://www.fieldbee.com/wp-content/uploads/2022/02/FieldBee-Web-Application-User-Manual-v.1.7.5.docx.pdf' target='_blank'>FieldBee Web app v.1.7.5</a></li><li><a href='https://www.fieldbee.com/wp-content/uploads/2022/02/v7.0.Diagram-of-connection-for-print-with-cover.pdf' target='_blank'>FieldBee Autosteer system Diagram of connections, checklists</a></li></ul> </span></div>